Chosen Solution Car started overheating. Reservoir filling up with antifreeze and bubbling. Did a block leak test which showed no combustion gases. Changed radiator cap. Did pressure test on radiator and found water pump was leaking. Replaced water pump. Bled air yesterday and drove car for about 30 minutes.A/c and heat worked well. Later yesterday I drove car about 5 miles, and it was doing fine. On way home I stopped at store....
Chosen Solution Replaced my screen about 3 times and my charging port went out. Replaced about 3 days after I get either no service, searching, or “service” (says I have bars but I don’t). I am wondering if the charging port would be the issue It can be a hardware issue. First rule out a bug by going to Settings>General>Reset>Reset Networks Settings. Next try your SIM in a different phone and a different SIM in your own phone....
Chosen Solution hi i have a problem with my phone.when i charge it it says charging but the battery is not increasing.i have to plug it twice or three times the cable before it can be charge.how do i fix it? You may have a damaged Lightning cable or Dock in the the phone. I would try another, known-good Lightning cable first to see if this solves the problem. They tend to have issues with the sheathing and outer conductor....
Chosen Solution Hi, my 1. gen. Apple Pencil suddenly wont interact with what’s on the screen of my iPad (which it has done since I bought it in early 2018). I don’t think the battery has been depleted, since I’ve been using the pencil daily and the issue occurred suddenly. Instead I suspect it has been damaged from being dropped on the floor, but a) is there any way of diagnosing what might be the matter?...
Chosen Solution A decent and viable alternative to consider is buying a used one in places like ebay, some are just second hand, others have been refurbished replacing a bad cord or broken case. Price would be about half of a new one. I purchased the MAGSAFE 2 60W adapter and am steaming about it. It looked fake, acted fake (takes too long to light up) and BROKE in about 2 1/2 weeks after purchase....
Chosen Solution Hi there, I have a MacBook CD 1,83 with some strange symptoms. 1/Bluetooth is, most of the time, not showing in the pref pan. It appears “when it wants” and disappears. 2/When bluetooth does not show, the MacBook do not want to go sleeping (when closing the Screen). Well it goes but awake after few minutes (the optical drive is working like when starting). And same if I leave it and wait it goes sleeping....
Chosen Solution I gave it to an authorized service center and they told me that my MacBook has had liquid damage so they have to change the logic board because it had corrosion on it. They also told me they had to change the battery because there is liquid stains on it. My question is do I have to replace the battery if it has stains on it can’t I just replace the logic board and get on with my MacBook Update (12/27/2017)...
Chosen Solution Hi, I dropped my phone and the screen completely cracked and went black. I could hear that messages where coming but could not unlock the phone. I have replaced the digitizer since then in the hope that this may fix the problem but with no results. I can turn the phone on but nothing else. I have tried the soft reset but it doesn’t seem to work. Any ideas of what may be wrong?...
Chosen Solution Hi, my phone still works fine, but the only issue is that my screen is black. I can only find tutorials that require I get a screen with a digitizer, but is there any way to only replace the screen. Not unless you have the appropriate equipment…which is more than a lcd/digitizer…you would need to use dry ice to freeze the loca glue making it brittle so it doesnt crack your lcd when u remove the digitizer…your better off just getting a new display
Chosen Solution Broken scanner glass,so I want to fix new glass? you can get the glass sets from places like this HP does not supply service manuals for printer / scanner hardware for disassembly. This video might help with the job. To get to the scanner glass you will need to remove the front display which can easily break your printer.
Chosen Solution Hi, I have i iPhone 5C but it has some damage on the sim card emplacement, i want to know is there an easy way to fix it ? Thank you Images : http://image.noelshack.com/fichiers/2015… Looking at the picture it seems like the plastic frame is damaged. This is what I would do: If the SIM card tray can get in and it works then do that. If you have lost the SIM Card tray you can get it on this website, here is the link: iPhone 5c SIM Card Tray If you are referring to the actual plastic housing you can replace the rear case and here is the manual link iPhone 5c Rear Case Replacement Now if there is damage to the sim card socket on the logic board there is no easy way to do this!...
Chosen Solution I recently dropped my flex4-1470 and now my audio is not working and neither is the headphone jack. How can I replace it? What parts do I need if I do? Hi, Here’s a link to the service manual for your IdeaPad. It details the necessary pre-requisite steps and then the procedures to dis-assemble the laptop to remove the relevant faulty parts. (if any). Scroll down to p.65 to view an exploded view of all the parts followed by the parts list....
Chosen Solution Hi After using bootcamp to install wondows 10 The wondows installation stratup and whene it finished it rebooted the mac stuck on the black screan i have dealt with it once before so I have of course tried reseeting pvram..etc nvram But this time no response + i can’t access the startup manager or recovery or hardware test mode I open the the device and removed the ssd after that i can access startup manager …etc and i was able to boot from external USB hard drive So what is the problem why the mac won’t boot if the ssd connected...
Chosen Solution My screen is broken and please help me to replace it Simply follow the guide here: Samsung Galaxy S7 Display Replacement You may need to purchase some of the metioned tools from iFixit in the guide.
Chosen Solution ‘bold text’ help Hi, To turn off the red light: With the phone in standby, open the menu and select Global Setup; select VMWI Reset, then select Yes. Here’s a link to the Uniden Dect 6.0. D1760 User guide. Scroll to p.13, (under Voice Message Notification) to view details of how to reset the light.
Chosen Solution I changed my LCD on my iphone 5, originally the LCD wouldn’t work, then when i changed it, it lit up. However only the backlight seems to be working. When i plug it into my laptop it seem to work because in itunes it was that i have put it in DFU mode and it needs restoring, so i restore and update the phone, then it says waiting for iphone....
Chosen Solution charging port stopped working. I cannot re-charge my kindle paperwhite. Has anyone had problem like this, and what can be done? Thank you, Sandra Sandra, sounds like you may have a loose USB port. Charge port is soldered to a circuit board inside the Kindle that allows battery to charge. If the soldered connection breaks, the battery no longer charges. If you google your problem you will see there was a problem with Kindles charge ports....
Chosen Solution Salut, Voici un lien vers le manuel de réparation d’un Dell Vostro 1500. ftp://ftp.dell.com/Manuals/all-products/… Le touchpad et le bouton touchpad font partie du repose-mains. Localisez la section dans l’index de contenu qui traite de la façon de retirer le repose-poignets. Cliquez sur le lien et cela vous amènera à la section qui décrit ce que vous devez faire pour retirer le repose-poignet afin d’accéder à l’ensemble du pavé tactile....
Chosen Solution Hi Together, I have changed HDD to SSD, was careful. Now I see that “Mac Fans Control” shows higher temperature of both CPUs and Platform controller hub die. I had impression that fan is running on quite minimum speed while I feel bottom of the Mac is getting hotter at place when fan is installed. Do you have an idea what could go wrong? Many thanks! It looks like TG Pro got you going!...
Chosen Solution Hi guys, I want swap my old HD4xxx (2x6pin power from board) for RX560/570/580 (1x8pin). But I am not sure what will be best power option ? All RX 5xx have max 225W what should be OK for board so no need PSU modification. Power over PCIe is 75W + 1x6pin 150W = 225W - it’s on the edge. And Also most of the GPU have 8pin instead 6pin so I need different cable....
