Posts

Chosen Solution had the scotter carb- cleand and was working ok. but now when started will not stay on ?? can some one Help? jessica, this could be caused by a few things like a to lean fuel/air mixture caused by air screw out of adjustment, clogged carburetor jet, clogged fuel line, clogged gasoline tank cap, incorrect carburetor fuel level (check your pilot valve and your float settings). My number one thing I would do is recheck the carb float and bowl, clean your tank multiple times and reevaluate....

Chosen Solution Hi, I bought this macbook off amazon a few days ago. It worked great for two days, then I left it plugged in overnight and when I tried to turn it on in the morning it showed me a black screen with a flashing folder icon with a question mark in it. I’ve tried many restarts since then but it has never showed me that icon again. Also, that morning the bottom of the computer was somewhat warm....

Chosen Solution Hi all, I’ve ran into something that I’ve never had before Long story short, I’ve got my customers Galaxy s5, it needed a new LCD. Customer says the phone was still working because she was getting notifications ect. I ordered the replacement LCD from eBay and it came with the mid frame also with instructions to change the mid frame too because the LCD is a non genuine one that won’t fit the original....

Chosen Solution every time that i power on, the computer starts to boot and sometimes does but then powers off or may not boot at all and powers off Please remove the three screws in the bottom of the frame and remove the housing. Press the reset button on the power supply located at the bottom of the frame where the power cord plugs in. You should also note two rest button about the middle of the motherboard just to the left of the diagnostic LED lights....

Chosen Solution Sony Bravia LCD tv model kvl 22bx310 blinks twice. What to replace or repair. Hi, Are you sure that it blinks twice or is it blinking green and amber? The service manual troubleshooting starts at 3 blinks and goes through to 7 blinks. The is no 2 blink error code shown. The green and amber blink error is shown on p.50 Hopefully this helps.

Chosen Solution I was replacing an iPad 4 and chipped the LCD FPC connector. I plugged in an LCD right away and it started without any problem - no screen issues whatsoever. So I took it out of the connector to assemble the digitizer and once I connected the LCD again I’ve got nothing. Not a flicker. My guess is the upper pins are impeding the bottom connection, but I don’t want tot risk irreparably damaging the device....

Chosen Solution I forgot my iPhone password the other day and accidentally disabled it, so I went to iCloud and selected ‘find iPhone’ and erased it, but it said that it will only be erased once it connects to wifi. What do I do? Lets backup here a bit… Do you have your iPhone now? If you do you can still recover things if you connect it directly to your computer if you have a local backup....

Chosen Solution is it possibly to use 2 16gb memory module? As long as you can return the module I would give it a try! Look at it this way you will have one spare slot. Kingston’s website will show you how much RAM and what kind to use in your iMac. It shows that the Max Memory is 16GB. But it also shows that you are unable to upgrade it because of the display....

Chosen Solution Hi I am seeing select network in my settings but it don’t have any Sims lots only an SD card slot why is that. Can it also use a sim card. A network can be more than a phone network . It would probably be referring to a WiFi network

Chosen Solution How do I know what model ZTE phone I have?. It just says ZTE on it. Where do I find that information? I got it fraom Qlink wireless with no information. Go to Settings –> About Phone. The model likely is written there. Model number should be printed on your phone battery or else you can easily look it up based on your IMEI using this site: imeitrackeronline.com...

Chosen Solution Hello, Do you know what points to check for a Canon 77D camera that has taken water? Are there fuses on the electronic cards to check? Thank you in advance Whenever it comes to liquid damage, you need to disassemble the whole device and give it a good inspection. If you can get someone to look at the components under a microscope, that would be even better. But it’s not very practical or economical to repair liquid damage....

Chosen Solution I tried to adhere a glass screen protector to my Samsung S9+ and made a mess of the loca glue. The glue got into the top speaker grill and I tried to clean it out with denatured alcohol / methylated spirits. Unfortunately, right now the speaker sounds crackly. I’m thinking the denatured alcohol got inside plus the partially dissolved loca glue. So what are my options? Can I fix the speaker by bathing it in more methylated spirits or buying some electronics contacts cleaner?...

Chosen Solution after one hour the engine still turns over but does not start had new carb plus fuel filter and air filter and fuel pump. wait for 5 minutes engine the fires up ok and able to complete my round of golf, but some times it happens again one or two hours later. Wait 5 minutes restarts. thank you John Briggs Hi, The information in this link may be of some help in finding your problem....

Chosen Solution I know they both use the same smaller camera but the plus uses another larger one. Can I put a small camera from an iphone 7 in the plus to test the logic board’s connection? Different camera setup (dual) & cable connections so it won’t work I have never taken apart an Iphone 7 or 7 plus, but looking at the compatibility listings here on IFixit, It doesn’t look like it would work out....

Chosen Solution 2002 model 917.271653 17 HP electric start, Briggs and Stratton engine. Turned key on. Heard a small pop. Won’t start. Solenoid won’t click. Have power to the white line to the solenoid. Checked the solenoid separately by putting power to terminals and got connectivity across power terminals. Cable to starter and cable to ground has connectivity. Jumped starter from battery and it cranks. Turn key, won’t start. No solenoid click....

Chosen Solution I have a 2012 MacBook Air (A1466) that had liquid damage. Everything points to something on the main board (will not power up). Tried new I/O board & new battery. The power adapter works. I have been looking on eBay and other sites, but I’m not sure which, if any, would be compatible. To be on the safe side take note of the logic board number..it’s written in quite small characters but can be found with a good light source....

Chosen Solution Hi all, I have a weird situation, previously I changed battery by myself, and damaged the trackpad ribbon while doing it at this time, battery was still detected, but the trackpad/keyboard were constantly connected and disconnected and then I tried unplugging the damaged trackpad ribbon, but it wasn’t solve the problem, my mac become very lagging and constantly searching for trackpad/keyboard since they were ‘unobserved’ (I saw it from Karabiner’s log), but at this time battery was not detected....

Chosen Solution Where can i get a replacement battery for my Galaxy 46mm lte watch(model SM-805F) Update (05/17/2022) Sounds good thks, cant find model SM-805F though. Lots of supplier’s online search with your model + replacement battery Guide on how to do it is here: Samsung Galaxy Watch Battery Replacement Sounds good thks, cant find model SM-805F though.

Chosen Solution I replaced the battery and it worked fine, then started dying at 10% charge, then 20%, now it dies at 63% of charge, reboots and shows 3%. It has been about 3 months since I did the battery change, and it keeps failing sooner every day. This seems to be a gas gauge problem. There is a battery gas gauge component (SWI) near the battery, if it has been knocked off or nudged it will cause the problems you are facing....

Chosen Solution My phone has been having a hard time charging while I hold it in my hand and it is connected to a charger. I believe it is because the port has been a bit worn from abuse, so would it be easier to replace the main board or just the port? Ok, so it would be “easier” to replace the whole logic board. But I wouldn’t call that cost effective....